BLOX. Here's how temperature monitoring prevents downtime.

September 9, 2025

High-voltage X-ray systems are designed for endurance and stability, but even the most robust technology can falter under the wrong environmental conditions. One of the most overlooked factors in system health is temperature, specifically, high ambient temperatures and clogged filter mats. These silent threats often go unnoticed until it's too late, leading to unplanned shutdowns or long-term hardware degradation. With BLOX, you gain early visibility into abnormal temperature patterns, allowing OEMs, integrators, and end users to act before damage occurs. This article breaks down what causes overheating, how to detect it, and how to stay ahead of costly surprises.

Overheating and its causes

Inside a high-voltage X-ray system, components like the power cells, tanks, and controller operate within defined thermal ranges. BLOX tracks these temperatures continuously and flags abnormal behavior through a two-threshold system:

The first threshold is a warning level, signaling that it's time to take preventive action.
The second threshold initiates a forced, irregular shutdown, halting operation entirely and immediately.

So what causes systems to overheat in the first place? Most cases can be traced back to one of three factors:

High ambient temperature: Often found in poorly ventilated rooms or warm production environments. In these cases, installing air conditioning or improving airflow can help maintain safe temperatures.
Clogged filter mats: In dusty environments, especially where IP 54 covers are used to shield the system, filters can clog much faster than anticipated. If not cleaned or replaced in time, airflow is restricted and heat builds up.
Technical issues: These include things like dust buildup in internal fans or malfunctioning sensors that no longer measure correctly. These are less common but still significant.

Even when the cause seems minor, the consequences of overlooking it can escalate quickly.

The consequences - more than just heat

One or two degrees over your usual operating temperature might not raise eyebrows, but when overheating goes unchecked, the impact is real and costly.
If you hit the second threshold, the system will shut down to protect itself. This results in unplanned downtime while it cools or until the filter mat is replaced. Even worse, if a system is allowed to operate near the threshold repeatedly, it places ongoing thermal stress on critical components like the generator. This leads to:

Increased wear on components
Higher risk of arcing in the tank
Shortened generator lifespan
Inconsistent image quality and longer exposure times

Over time, you're not just facing maintenance tasks, you're risking the stability and output of your entire system.

How to spot overheating with BLOX

Fortunately, overheating doesn't have to catch you off guard.

BLOX gives you the tools to identify rising temperature trends before they trigger any alarms. Start by checking the Temperature tab in your BLOX dashboard. Look for:

Consistently stable values: These are a good sign, even if occasional peaks occur.
Steep upward trends: A persistent climb toward the warning threshold means action is needed now, not later.

In some cases, users have noticed the warning alerts but continued operating the system just below the threshold for weeks or even months. This behavior quietly increases thermal strain and can eventually lead to irreversible component wear. Our advice, don't wait. Once you see a pattern, act early. BLOX is built to catch these changes in time, if you use the data.

1. Slow Incline (Stable Situation):
The temperature trend shows a gradual, stable increase, no immediate action needed, but continue to monitor.

2. Steep Incline (Critical Situation):
A sharp rise toward the threshold is clearly visible, this is a warning sign. Immediate action is required to avoid shutdown.

3. We've seen situations where customers acknowledge the alert but continue operating the device close to the threshold for months without taking action. This sustained thermal stress puts unnecessary strain on the generator, increases the likelihood of arcing in the tank, and accelerates overall wear.

A word of caution: delays only make things worse. Early action is key.

Recommendations

If BLOX shows rising temperatures or alerts related to clogged filters, here's how to respond:

Monitor the ambient environment: Use external room sensors or BLOX's internal readings to assess whether the room temperature is too high.
Inspect and replace clogged filter mats: This is often a simple fix that the end user or customer can quickly carry out, dramatically reducing operating temperatures.
Use BLOX to track temperatures over time, not just when alerts pop up.
Consider installing air conditioning in high-temperature areas, especially if overheating is a recurring issue.

By combining simple steps with BLOX insights, you can move from reactive troubleshooting to preventive care, extending equipment life and improving system performance.

A few real-world scenarios we've encountered:

Unplanned Downtime: In one installation, a steep rise in temperature was recorded over several days, ignored until the system shut down mid-operation. Only then did the team discover the filter mat was completely clogged. They replaced the filter, improved ventilation, and prevented any downtime from occurring.
Ideal Scenario: In a third installation, the team had set up routine checks using BLOX trend data. As soon as the temperature began to rise, they took action. The system never approached the warning threshold, and uptime remained uninterrupted.

Let BLOX be your early warning system

High temperatures and clogged filters may not make headlines, but they do cause headaches. BLOX transforms hidden risks into visible insights, helping you protect your investment, avoid downtime, and keep performance high. Not sure if your system is running too hot?

Check BLOX today and take control of your system's temperature health, before it becomes a problem.

Latest three news

Welcome Andreea!

November 2, 2026

Meet Andreea Vasiliu, our new Vice President of Global Sales! Andreea brings extensive international sales and leadership experience and knows Comet well from her previous roles within Plasma Control Technologies. During more than eight years with the company, she held several global and regional sales leadership positions, most recently as Director Sales EMEA and Vacuum Capacitors Global. Since 2024, she has served as General Manager Europe and RoW at VAT Group.

Need for Speed: Boosting X-ray Inspection Speed in Advanced Electronics

October 28, 2026

As electronics become more powerful and advanced packaging technologies more complex, manufacturers face the challenge of detecting ever-smaller defects without reducing throughput. Optical inspection methods cannot reveal the buried structures found in high-power electronics, chiplets, HBM, through glass vias (TGVs), and advanced 3D packages. X-ray inspection and automated X-ray inspection (AXI) provide the required visibility, but higher resolution and penetration have traditionally come at the expense of speed. Recent advances in micro and nano focus X-ray source technology are overcoming this trade-off by delivering higher photon flux, improved contrast-to-noise ratio, and faster imaging. In this post we review these developments in high-power electronics, where higher voltage and power are required to penetrate through dense structures while maintaining micro-scale imaging, and advanced packaging where increasing complexity from vertical integration and sub-micron resolution combine. We highlight how increased throughput can be achieved while maintaining reliable defect detection.

Focus topic. A conversation with Jan Bressendorff and Allen Gress about pipeline weld inspection

October 8, 2026

On a pipeline job, the X-ray system is chosen for the weld, not from a catalog. Pipe size and access determine how the crew can inspect it. The procedure sets what the image must show. Heat, weight and exposure time shape the working day. A poor choice can cost hours. A good one helps the crew get an image the inspector can assess without needless delay.

Is your module running too hot?